humber sceptre mk3 (arrows)

turbinecol
Posts: 125
Joined: Wed May 02, 2007 4:14 pm
Location: South East England

Re: humber sceptre mk3 (arrows)

Post by turbinecol » Tue Jun 18, 2013 1:53 pm

That is looking really rather good. Notice you have a single carb there. I have a similar set up on my Hunter and it is really quite good, much more spritely than you'd believe and easier to set up than the twins.

I guess once you have it back together you could always consider the spray shop in future, if you time and money. Nothing is cheap these days unfortunately, and access to decent facilities for spraying (safely and with good quality) is another matter.

hoppo
Posts: 90
Joined: Thu Dec 06, 2012 12:17 pm

Re: humber sceptre mk3 (arrows)

Post by hoppo » Tue Jun 18, 2013 4:36 pm

Why Thank you kind sir....... Looks can deceive This car was allways a budget restoration I have tried to reuse as much as possible but of course when you dismantle a car some items fall apart, Some are just past it and some are just not the correct part !!! today I was fitting the new brake shoes when I got the car the old shoes and stuff was in the boot, so all cleaned up spot of grease on the back plate and .....the drums would not go on...not the adjuster ?? takeing a long hard look I found the small horns on the wheel cylinder pistons was fouling the stud on the shoe for the adjuster, so that had to be sorted. the cylinders are the right bore but maybe for another model, any way ok now....brakes now ready to bleed andcheck for leaks.... everything will need to be tested asi have no idear if it is all good or not like the diff? will the speedo be out? 3.7 diff with a manual box Mmmmm! ect ect will keep you all posted BFN hoppo

turbinecol
Posts: 125
Joined: Wed May 02, 2007 4:14 pm
Location: South East England

Re: humber sceptre mk3 (arrows)

Post by turbinecol » Wed Jun 19, 2013 11:46 am

Do you have an overdrive J type or D type overdrive gearbox?

I have a 3.70 axle in combination with a J type overdrive box on the Hunter, and it reads bang on the money with GPS (corrects the usual over-read basically)
Last edited by turbinecol on Thu Jun 20, 2013 8:04 am, edited 1 time in total.

hoppo
Posts: 90
Joined: Thu Dec 06, 2012 12:17 pm

Re: humber sceptre mk3 (arrows)

Post by hoppo » Wed Jun 19, 2013 12:28 pm

Just the standard hunter four speed ? would have liked the overdrive but was not available at the right price, I have been told (not sure of how true and what you have to change)That the ford type9 5 speed box fits ? any idears???

turbinecol
Posts: 125
Joined: Wed May 02, 2007 4:14 pm
Location: South East England

Re: humber sceptre mk3 (arrows)

Post by turbinecol » Thu Jun 20, 2013 8:00 am

I would say stick with the standard Hunter box. The type 9 5 speed tends to feel very sloppy and unless you find a low mileage one, they can make a racket when they are a bit worn out. I had one on a Granada, which was a fine car, but it was getting a bit worn out at the end, and leaking from all its seals. You'll find the 4 speed Hunter has a much nicer feeling shift, and better suits the car in my opinion.

If an overdrive box crops up at an opportune moment, it's easy to just drop that back in.

hoppo
Posts: 90
Joined: Thu Dec 06, 2012 12:17 pm

Re: humber sceptre mk3 (arrows)

Post by hoppo » Thu Jul 04, 2013 9:20 am

Ok. Standard box it is.... rear panel painted and all lights and trim fitted to rear.gearbox wired in and reverse light work fine rigged up front and side indicators and they work as well!! . Dash is in all warning lights ang gauges work even the low fuel light checked with gauge out on my lap . The gauge works on resistance and at first i only got 3/4 max then cleaned all connections and the gauge almost max so that maybe how it will stay. Just waiting for Speedy to deliver new tank seal and ring then i will fire up the beasty and check for leaks ect. I have a friend coming over next week to help fit the new brown vinyl roof....... Not looking forward to doing it .... never done one before... The bit I dread is the rear corners there is a three way fold to do and I anticipate much frustration and bad language... No change there then... will post again in a few weeks

turbinecol
Posts: 125
Joined: Wed May 02, 2007 4:14 pm
Location: South East England

Re: humber sceptre mk3 (arrows)

Post by turbinecol » Thu Jul 04, 2013 12:09 pm

Good luck with the roof, it must be one of those things ideally best left to the experts, but go for it!

I had a real struggle finding a replacement fuel tank sender - standard Hunter ones have a single connection to the gauge - the warning light is a second connection. All the ebayer ones are single connection, and Speedys haven't had a dual connection one for years - so if yours work even partially, enjoy that for now

hoppo
Posts: 90
Joined: Thu Dec 06, 2012 12:17 pm

Re: humber sceptre mk3 (arrows)

Post by hoppo » Sun Jul 07, 2013 10:34 pm

tank unit sorted,,,, turned out to be a badley adjusted voltage stabalizer reads fine now... here is lates photo
You do not have the required permissions to view the files attached to this post.

turbinecol
Posts: 125
Joined: Wed May 02, 2007 4:14 pm
Location: South East England

Re: humber sceptre mk3 (arrows)

Post by turbinecol » Tue Jul 09, 2013 8:59 am

tremendous. I always love with the Sceptre the bit when the front grille goes on - turns it from a Hunter into something a bit more special.

What is the score with the bumpers?

hoppo
Posts: 90
Joined: Thu Dec 06, 2012 12:17 pm

Re: humber sceptre mk3 (arrows)

Post by hoppo » Tue Jul 09, 2013 9:26 pm

working on them as we speak, there not in the best condition but not beyond use. waiting for some new bolts from summit motors my friendly MG dealer and two stainless steel no plate backings....... getting excited now but must always keep in mind that Nothing has been tested yet... gearbox axle ect
You do not have the required permissions to view the files attached to this post.

turbinecol
Posts: 125
Joined: Wed May 02, 2007 4:14 pm
Location: South East England

Re: humber sceptre mk3 (arrows)

Post by turbinecol » Fri Jul 12, 2013 11:54 am

I sprayed the back of my bumpers with some Hammerite or something like that, might just help keep the rust at bay- I didn;t even mask them, just polished off the overspray from the front surface here and there. The over-riders are prone to rusting too, so do the same with those.

sceptictank
Posts: 77
Joined: Fri Jun 03, 2011 4:28 pm

Re: humber sceptre mk3 (arrows)

Post by sceptictank » Sat Jul 13, 2013 12:46 pm

Excellent progress and nice to see someone 'coachpainting' their car for a change!

hoppo
Posts: 90
Joined: Thu Dec 06, 2012 12:17 pm

Re: humber sceptre mk3 (arrows)

Post by hoppo » Mon Aug 12, 2013 1:18 pm

still moving on the good weather has been kind
You do not have the required permissions to view the files attached to this post.

sceptictank
Posts: 77
Joined: Fri Jun 03, 2011 4:28 pm

Re: humber sceptre mk3 (arrows)

Post by sceptictank » Mon Aug 12, 2013 3:17 pm

Paintwork looks good - what paint did you use?

hoppo
Posts: 90
Joined: Thu Dec 06, 2012 12:17 pm

Re: humber sceptre mk3 (arrows)

Post by hoppo » Mon Aug 12, 2013 4:05 pm

craftmaster paints of cambridge, I used mid brunswick green with an undercoat after some false starts I found adding up to 20% of "owatrol oil" to the gloss helped a lot. craftmaster paints sell "purdy" brushes I just asumed they new what was best, however I bought a 3" harris brush from b&q and a mixing pot and the results are super o/k you could find fault with some panels as they where false starts, brushing is a labour intense job as my car was brushed when I got it I had to decide if i stripped it back to metal or pay out to seal the paint from cellelose then I had to buy lots of things to spray ect the cost just kept going up and up so brushing was the choice, Ithought it would be simple... not so there is a bit of technique and some skill but as allways preperation counts for a lot, I am now at the stage where my shoulders are worn out so have accepted how things are and at a later date I can allways paint a panel again no masking up and the paint cover is very good

Post Reply