Page 1 of 1

convert auto to manual

Posted: Thu Nov 21, 2013 8:00 pm
by johncon
Hi Guys I am new here . thank you for accepting me to your site
I have recently bought a very nice 1971 sceptre mk3 automatic . But I would like to convert it to manual .
I have located a manual overdrive gearbox /prop-shaft /flywheel /clutch/ pedal box ect . but the bloke that has all the parts says I need to change the engine as well ! is this so ? I don't want to swap the engine as mine is a great runner and not big mileage .
Any help gratefully received
Thanks
John

Re: convert auto to manual

Posted: Fri Nov 22, 2013 12:25 am
by thowman
In short - he's talking absolute rubbish.

You can change the gearbox and keep the existing engine. Just take off the auto box, remove torque converter mounting plate on the end of the crank, and then put the flywheel in its place, then the clutch and then the gearbox. If you have all the parts you have listed, then it should be reasonably easy.

Ask him why you need to change the engine - I need a good laugh.

By the way, make sure the gearbox is off a Hunter shaped car. They are different to earlier ones (the bell housing is longer and tilts the engine slightly compared to the earlier shaped sceptre.

A

Re: convert auto to manual

Posted: Fri Nov 22, 2013 7:21 am
by johncon
He tells me the crankshaft is different and the flywheel wont fit ! I am a mechanic by trade and have done this job on many Fords ect in years gone by and not come across the problem before . but the car is in everyday use and am planning to do the job in a long weekend !

Re: convert auto to manual

Posted: Fri Nov 22, 2013 11:27 am
by thowman
I don't think this is the case. I have never got around to actually doing the conversion, but I have taken an auto box off a super minx, and the crank looks the same to me, with four bolts on it, just with a small plate attached to it instead of the flywheel so that you can bolt the torque convertor on it when the box is actually on the car.

I cannot believe that Rootes would have a different crank for the auto engine - not even they were crazy enough to do that. I'd eat my hat if it were true.

Re: convert auto to manual

Posted: Fri Nov 22, 2013 9:47 pm
by turbinecol
I just checked the parts manual too - it's a common crank. Just need the correct adaptor parts to the torque convertor and you're there.

Re: convert auto to manual

Posted: Fri Nov 22, 2013 11:11 pm
by johncon
thank you I know some 60's/70's cars the crank could be different but now i am starting to think this guy might be misinformed rather than just trying to sell me a engine . will probably just buy the gearbox and everything else of him and take a chance on getting the job done in a weekend ! if anyone else is in need of parts once i have done a deal with him i will share contact details for him he has got or broken 3/4 sceptre mk3's

Re: convert auto to manual

Posted: Wed Nov 27, 2013 6:01 pm
by hoppo
Hiya, just done my one it is quite easy dont forget the clutch slave and master also the pipe, when putting it together you can assemble the pedal box and then pop it through the bulkhead saves a bit, also check propshaft length you might have the split prop my car had no prop but standard one fitted well, look for a fine spline on the box and prop corse splines are the audus group and will not fit.. good luck hoppo psthe auto diff shoul be a 3.7 so check your speedo when finished

Re: convert auto to manual

Posted: Wed Nov 27, 2013 6:04 pm
by hoppo
sorry just remembered the centre console has a long oblong cut out for the auto the man has a 2" square I boughth a veneer and ironed it on and a bit of varnish .....

Re: convert auto to manual

Posted: Wed Nov 27, 2013 10:04 pm
by johncon
thanks for the positive feedback guys i really do appreciate it .
i really did not see why i should have to change the engine. if i had to change the engine i would probably have gone for a modern engine setup and did not want to do that either .