Page 1 of 3

newbee needs advise

Posted: Sat Jun 07, 2008 10:23 pm
by rooted
Hi all , just got myself a MK 3 sceptre , runs fine and moted no real rot to speak off HOWEVER the rear axle / diff screams like a banshee .Is there anything i can do with it ordo i need a new rear axle , if so where can i get one . its fine off load but is terrible above 60 , so much so my ears hurt :shock: please help

Re: newbee needs advise

Posted: Sun Jun 08, 2008 12:05 pm
by BeJay
Hi,
I assume you've checcked that there is actually oil in the diff ?? if so then just check out the 'Mk 111 Sceptre spares' thread by humberjohn just a little further down the page, he's put his contact number in there so just give him a bell, by the way you only need to change the diff rather than the whole axle if you want, hope this helps.
cheers, Jack.

Re: newbee needs advise

Posted: Sun Jun 08, 2008 2:01 pm
by rooted
How do you you check if theres oil in it , there are no plugs ( either drain or topup ) on it , only what appears to be a vent plug on the top , i pulled the cap off and there seems to be a valve in it , sorry to sound a bit thick but im more used to hillman Imps than these :oops:

Re: newbee needs advise

Posted: Sun Jun 08, 2008 3:43 pm
by BeJay
....no plugs :shock: :shock: .....I think that what you checked was indeed the axle breather/vent unit if it was on top of the axle (No 1 in the pic) but you should also have a drain plug on the bottom of the diff casing (No 2 in the pic) and a filler/level plug on the top half of the diff itself (No 13 in the pic) or at least something very similar as this is an axle from a Mk2 car, hope this helps.

cheers, Jack.

Image

Re: newbee needs advise

Posted: Sun Jun 08, 2008 6:07 pm
by Dorsetflyer
Yes the MK111 version is the same as the diagram above for the vent, drain plug, and level/filler plug, so you should be able to find it easily.

Re: newbee needs advise

Posted: Sun Jun 08, 2008 6:34 pm
by rooted
Thanks everyone. Good news and bad really , good news is ive found the filler , bad news its snaped off so i cant fill it up ,thats why i couldnt see it . kinda stuffed now , i thought it might be an allen key jobby untill using a torch and mirror its uumm mullered , what should be there nut / square peg or what .oh b"£ , anyone got any ideas now :cry: :cry: thanks in advance . ps anyone near Yeovil in the club.

Re: newbee needs advise

Posted: Sun Jun 08, 2008 7:21 pm
by rooted
Hi all , perhaps i should describe to you all what im dealing with . Its possibly one of the most rot free ones ive ever seen , its never been welded and apart from a little bit of rust on one wheelarch ( just the inner lip bit easy to do ) its truely wonderfull underneath , original sills , A1 front wings , perfectly streight in fact the shell is great .And the reason for this is its been stood since 95 in a barn . it was MOTed in Guernsey in oct 07 :shock: :o but never put on the road over here , i think its worth doing but i feel a battle coming on . Today , fed up with the axle probs i decided to sort some other ones out , first off the bonnet release cable was seized , done that , sorted out the no brake lights ( switch ) , sorted the no main beam flash ( switch) MOTed uh :shock: , then i went for the no heater bit , the rust that came out of it was enough to build a Fiat out off , heater valve once id found it (what donut at Chrysler decided to put it there :shock: ) was blocked solid AND more of a worry , no stat fitted , anyway the heaters now like the fires of hell although she runs a little bit warm for my liking ( a couple of mill above N ) all seems better , What stat should they have :?: , ive fitted an 88 one coz thats all i had , enough rambling for now , wish me luck :cry:

Re: newbee needs advise

Posted: Mon Jun 09, 2008 5:29 am
by BeJay
Hi again,
only thing I can suggest is to centre punch the plug as close to the edge of it as you can, then hold the punch at about 45 degrees to the vertical and give it some welly, but make sure you're hitting it in the correct direction to undo it (anticlockwise looking from the top) I've used this method with some success before now, :lol: :lol: either that or drill into it from the top and then use some decent screw extractors on it, either way you're going to need to take the diff out to get enough room to work on it so maybe it may be as well to just get another diff to swap it with and then sort yours and keep it as a spare, postage is liable to be the crippler as diffs are so heavy but give
these people a ring and ask if the diff is available and how much they'd charge for postage.

cheers, Jack.

Re: newbee needs advise

Posted: Mon Jun 09, 2008 5:55 pm
by rooted
cheers for that bejay , i may have soursed another axle , only thing is ive no idea how much to offer him and hes no idea what to charge me , roughly how much do they fetch , odviously want it as cheap as i can but i dont want to rip anyone off either. :D

Re: newbee needs advise

Posted: Tue Jun 10, 2008 2:50 pm
by BeJay
rooted wrote: roughly how much do they fetch , odviously want it as cheap as i can but i dont want to rip anyone off either. :D
.......how long's a piece of string :lol: :lol: it depends how badly you either need one or want to get rid of one, I'd have thought around £30 - £40 'ish was reasonable for a "good" complete axle, all I can tell you really is if you settle on a figure that you're both happy with then neither of you will feel ripped off, I'd offer to lend a hand but Yeovil is a bit too far from Peterborough, hope you get it swapped over OK if you get the axle.

cheers, Jack.

Re: newbee needs advise

Posted: Tue Jun 10, 2008 8:02 pm
by rooted
Thanks anyway bejay , had another play tonight , got the clock working and restrung the drivers seat as it was a bit saggy , oh and fixed the horn that had been rewired on a bypass circuit off of the brake light circuit :o :shock: :? , just need this axle and i think its ready , :D

Re: newbee needs advise

Posted: Thu Jun 12, 2008 6:51 pm
by rooted
Hi the new pest again , where can i get a new windscreen seal from , after its 15 yrs hybernation in the dry rain has turned it into a pond :o :shock: :cry:

Re: newbee needs advise

Posted: Fri Jun 13, 2008 11:30 am
by BeJay
.....try this link click on the logo to enter the shop, click on Sceptre I - II on the right, scroll down and click 'Last' (page 4 of 4) you should find it 3rd up from bottom part No 2225292, you'll have to call them to check availability.

............cheers, Jack.

Re: newbee needs advise

Posted: Mon Jun 16, 2008 5:04 pm
by rooted
Hi just been offered a rear axle from an H reg Sceptre , are they the same , will it fit. HELP i need to know ASAP so i can get it. Mines an N reg one.

Re: newbee needs advise

Posted: Mon Jun 16, 2008 5:56 pm
by rootesmadnick
dont know about the axle but welcome to the forum !! seems your getting stuck in good and proper !!
if you find out the correct oil quantity for the diff you could alwyas drain whats left in it and put the correct quantity through the breather if it undoes ok