Hello everyone, my name is Marco and I hail from New Plymouth, New Zealand. I have had in my possession for a number of years a 1973 Sceptre. My car is something of an oddity in that it was badged and registered from day one as a Sunbeam Sceptre. I have never seen another one. There are very few Humber badged Sceptres in this country as it is. This car came to me by an interesting manner. It was gifted to my best friend by a complete stranger (long story) and when he lost the means to store it, it was given to me. It then sat in storage for years until we moved house, whereupon with some encouragement I got it running and drove it onto a transporter to move cross country. I have now built a large workshop at home, so I can get stuck into the restoration. I have no experience of Rootes cars other than our Avenger family car when I was very young, and a Hunter estate when I was even younger (doesn't count really).
The car is metallic green and manual/overdrive with a vinyl roof. Rust has got into it and there are lots of old filler bodge repairs to discover and undo. Wish me luck! I'll try and get some pictures up when I figure out how.
Hi all, new member from New Zealand
-
sceptictank
- Posts: 77
- Joined: Fri Jun 03, 2011 4:28 pm
Re: Hi all, new member from New Zealand
Hi and welcome to the forum.
Sounds like an interesting project so please do post pics as you go along. It can be a quiet on here sometimes but please keep us posted.
Hoppo's Sceptre rebuild thread is well worth a visit : http://www.rootes1725cc.info/board305/v ... f=3&t=1124

Sounds like an interesting project so please do post pics as you go along. It can be a quiet on here sometimes but please keep us posted.
Hoppo's Sceptre rebuild thread is well worth a visit : http://www.rootes1725cc.info/board305/v ... f=3&t=1124
-
Marco Polo
- Posts: 9
- Joined: Sat Sep 14, 2013 2:44 am
Re: Hi all, new member from New Zealand
Here is a pic for starters...
You do not have the required permissions to view the files attached to this post.
-
hoppo
- Posts: 90
- Joined: Thu Dec 06, 2012 12:17 pm
Re: Hi all, new member from New Zealand
Hi Marco, nice to meet you, I seem to remember reading on a forum somewhere on the net about export models being badged sunbeam, not sure why though? your car looks great, ok some rust but hey if it had no rust it would'nt be in your garage, I am well on the way to finishing my car and on the way encounted many problems....... like you I removed the roof and found some of the dreaded tin worm lurking in damp corners. I notice from the photo you still have the front corner trim pieces in place these are held on by a "pop" rivet try not to drill out with too big a drill as a larger rivet upsets the fit when going back on, I used a stanley knife blade to strip the old glue from the roof, mine was so dry it came away like powder needing only minor treatment to stabelise, the chromes around the doors can be very fragile and when removing be carefull not to bend , again I found that easing off with a pair of parrot nosed pliers and gently working a blade behind worked well the hard bit on mine was the corners just take your time and remember the phrase "it is not available any more" try to save every thing on the strip down lable if you can and small items go well in an old biscuit tin..
Several biscuit tins in fact. the car is a very simple design and has no real vices May I sugest strip off all the mechanical Put the body on stands and poke about a bit to find the extent of the tin worm damage. replacement panels are rare so work on the idear that yoou will have to make up parts as you progress. get the best welder you can afford (it can be sold after) some sheet steel, tin snips, If you can a small angle grinder is usefull to cut larger parts and clean up whats left to weld to although when in the striped out phase it can be very down heartening to see piles of bits and a rotten body needing loads of welding..... I just broke it down into smal bits and set myself a target to "weld the cill" then weld the lower wing ect ect Please dont rush it you will get to the stage when it seems you are getting nowhere But like the phoenix it will slowly arrive "finished", If yyou would like any help please maile me as I now know much more than I did when I started this project in dec 2012............. Good Luck hoppo
Several biscuit tins in fact. the car is a very simple design and has no real vices May I sugest strip off all the mechanical Put the body on stands and poke about a bit to find the extent of the tin worm damage. replacement panels are rare so work on the idear that yoou will have to make up parts as you progress. get the best welder you can afford (it can be sold after) some sheet steel, tin snips, If you can a small angle grinder is usefull to cut larger parts and clean up whats left to weld to although when in the striped out phase it can be very down heartening to see piles of bits and a rotten body needing loads of welding..... I just broke it down into smal bits and set myself a target to "weld the cill" then weld the lower wing ect ect Please dont rush it you will get to the stage when it seems you are getting nowhere But like the phoenix it will slowly arrive "finished", If yyou would like any help please maile me as I now know much more than I did when I started this project in dec 2012............. Good Luck hoppo
-
Marco Polo
- Posts: 9
- Joined: Sat Sep 14, 2013 2:44 am
Re: Hi all, new member from New Zealand
Thanks for the encouragement and advice. This is most certainly a long term project! I have found to my horror the extent of some of the bodges now that I have spent an hour poking around the body. There is so much filler it is quite depressing. Also some swine has tack welded a large steel patch ON the roof, then skim bogged (we Kiwis call filler 'bog') the whole roof before glueing a new top on, probably at least 15-20 years ago. Not sure how I will go about fixing that..
Thus far I have found perforating rust in both sills, lower front guards, A pillars, roof, bonnet, all doors, a chassis outrigger under the passenger footwell, lower boot behind the left rear wheel. There is also a lot of filler in the tops of the front guards, roof (as mentioned) windscreen surround... Oh boy! I have a clean bonnet for it. I also have 4 mint rust free Hunter doors but is it me or is the swage line very slightly different?
On the plus side, engine, gearbox, overdrive and diff seem fine. The wiring is messy ( I hate wiring) and the woodwork is tired. I have complete set of replacements for most of the wood trim.
First order of business is to finish building my workshop, then invest in shelving and storage, then gut the body shell and witness the true extent of the rot!
Thus far I have found perforating rust in both sills, lower front guards, A pillars, roof, bonnet, all doors, a chassis outrigger under the passenger footwell, lower boot behind the left rear wheel. There is also a lot of filler in the tops of the front guards, roof (as mentioned) windscreen surround... Oh boy! I have a clean bonnet for it. I also have 4 mint rust free Hunter doors but is it me or is the swage line very slightly different?
On the plus side, engine, gearbox, overdrive and diff seem fine. The wiring is messy ( I hate wiring) and the woodwork is tired. I have complete set of replacements for most of the wood trim.
First order of business is to finish building my workshop, then invest in shelving and storage, then gut the body shell and witness the true extent of the rot!
-
turbinecol
- Posts: 125
- Joined: Wed May 02, 2007 4:14 pm
- Location: South East England
Re: Hi all, new member from New Zealand
Good posts guys.
marco, the doors are exactly the same in terms of the frame and outer skin, but obviously you may have to swap over different trims between the two, chromework around the frame being the major item, and potentially having to fill in some holes on the exterior panel where the Hunter has trim strips instead of Sceptre stripes. Good luck...
marco, the doors are exactly the same in terms of the frame and outer skin, but obviously you may have to swap over different trims between the two, chromework around the frame being the major item, and potentially having to fill in some holes on the exterior panel where the Hunter has trim strips instead of Sceptre stripes. Good luck...