I've have a 1961 super minx with the 1592cc engine (cast iron head.)
Were all of the cast iron heads off of the 1592cc rootes engines the same?
e.g. Could I find a manifold off of an alpine twin carb setup and install on my 1592 engine?
Regards,
Dana
Compatible exhaust manifold for 1592cc engine?
-
rhythmrider
- Posts: 89
- Joined: Mon Sep 02, 2013 6:58 pm
-
rhythmrider
- Posts: 89
- Joined: Mon Sep 02, 2013 6:58 pm
Re: Compatible exhaust manifold for 1592cc engine?
I guess I should also ask, are the cast iron 1592 and 1725 port configuration compatible?
So the manifolds for the cast iron heads would be compatible between the two?
So the manifolds for the cast iron heads would be compatible between the two?
-
thowman
- Posts: 79
- Joined: Mon May 24, 2010 9:31 pm
Re: Compatible exhaust manifold for 1592cc engine?
All the cast iron head manifolds are the same, and are different to the alloy heads. The inlet and outlets on the cylinders 2 and 3 are in different positions between the different head types, so in short a manifold off an alpine wouldn't fit.
I know someone who fitted an alloy head to a cast iron engine, and wondered why it never worked properly - of course, he didn't change the camshaft!
I know someone who fitted an alloy head to a cast iron engine, and wondered why it never worked properly - of course, he didn't change the camshaft!
-
rhythmrider
- Posts: 89
- Joined: Mon Sep 02, 2013 6:58 pm
Re: Compatible exhaust manifold for 1592cc engine?
Andy,
Thanks for the reply. It's good to know that all of the cast iron heads had the same ports.
There were some cast iron heads on early Alpines here in the USA. But they are not very common.
I think they had the dual Zenith down draft carb setup.
regards,
Dana
Thanks for the reply. It's good to know that all of the cast iron heads had the same ports.
There were some cast iron heads on early Alpines here in the USA. But they are not very common.
I think they had the dual Zenith down draft carb setup.
regards,
Dana
-
thowman
- Posts: 79
- Joined: Mon May 24, 2010 9:31 pm
Re: Compatible exhaust manifold for 1592cc engine?
I never heard of there being any cast iron alpines, but that doesn't mean there weren't any made. I just restored a series 1 for someone, but that had am alloy headed engine.
An easy improvement is to fit a weber carb, which you should be able to source in the US without a problem. It's a 34 ICH, I believe. Start off with jettings for a land rover, and that should work. It's a common "improvement" over here for these engines.
An easy improvement is to fit a weber carb, which you should be able to source in the US without a problem. It's a 34 ICH, I believe. Start off with jettings for a land rover, and that should work. It's a common "improvement" over here for these engines.
-
rhythmrider
- Posts: 89
- Joined: Mon Sep 02, 2013 6:58 pm
Re: Compatible exhaust manifold for 1592cc engine?
Thanks for the tip on the 34 ICH. I might just go that way. Since They are available online NEW for only $150
But since I did pick up a rebuild kit for the old Zenith, I think I will do that first for the fun of it.
I see where I was confused about the Alpines with cast iron heads.
There was a fastback sedan sold here in USA that was named the Alpine GT. AKA Rapier in the UK.
Some of those did have cast iron heads.
But since I did pick up a rebuild kit for the old Zenith, I think I will do that first for the fun of it.
I see where I was confused about the Alpines with cast iron heads.
There was a fastback sedan sold here in USA that was named the Alpine GT. AKA Rapier in the UK.
Some of those did have cast iron heads.