A fair bit of help needed with a MK1

Post Reply
SegaSceptre
Posts: 66
Joined: Mon Oct 13, 2008 7:32 pm

A fair bit of help needed with a MK1

Post by SegaSceptre » Sun Nov 02, 2008 6:59 pm

Ive got a few problems that some assistance is needed with. First of all is the slave cylinder, does any one have a solution to stopping the piston popping out? Does anyone have a gasket set for dual Zenith carbs?

The Garage is also full of spares, some of which are from a mk2 Sceptre aswell as a MK1 which may be of use to some of you. My Uncle would prefer a trade but if the item is a bit tatty and no one really wants to give anything for it then hes happy to let it go.

dave B
Posts: 9
Joined: Sat Aug 09, 2008 4:43 pm

Re: A fair bit of help needed with a MK1

Post by dave B » Wed Nov 05, 2008 4:56 pm

Hi unfortunately I cannot help your problem, but regarding your spares, do you have an overdrive gearbox and prop, I am in Somerset and if you have would collect quickly. Best regards Dave B.

Dorsetflyer
Posts: 44
Joined: Tue Dec 04, 2007 3:25 pm
Location: Weynouth, Dorset

Re: A fair bit of help needed with a MK1

Post by Dorsetflyer » Thu Nov 06, 2008 11:44 am

On your first point, I have used a thick rubber band wound tightly round the body of the cylinder to good effect.
You can also use wire twisted tight enough to stop the piston from coming out.
On your second point, I would try 'BURLEN' fuel systems who are in Salisbury, Wilts. Alternatively there is a company in Leighton Buzzard, Bucks who do Zenith spares and also exchange carbs. I cannot remember their name offhand but they do advertise in 'Practical Classics'.
Regards
John

rootesmadnick
Posts: 272
Joined: Fri Feb 01, 2008 7:42 pm
Location: lumbering in a humber somwhere !!
Contact:

Re: A fair bit of help needed with a MK1

Post by rootesmadnick » Thu Nov 06, 2008 6:36 pm

hi, if the piston is popping out when your actually trying to use the car then there is either serious wear somewhere or if its possible the cylinder is on the wrong side of the bellhousing (think its possible to bolt it on the outside instead of inside but not sure been ages since I took one off)
if its to stop it popping out when transportingit or sending it then a cabletie through the bolt boles and across the front works well
I fix things!!

SegaSceptre
Posts: 66
Joined: Mon Oct 13, 2008 7:32 pm

Re: A fair bit of help needed with a MK1

Post by SegaSceptre » Sat Nov 08, 2008 12:17 pm

Hi, thanks for the replies and tips, Dave B Ill see if theres one in the garage and if my uncles happy to part with it, Ill try and get back to you about it tomorrow evening or next Saturday depending on what time Im at the garage.

SegaSceptre
Posts: 66
Joined: Mon Oct 13, 2008 7:32 pm

Re: A fair bit of help needed with a MK1

Post by SegaSceptre » Sun Nov 09, 2008 5:36 pm

You've got PM Dave.

Anyone need a Grey interior set for a mk2 Sceptre? Theres on in the Garage, a little tatty but serviceable. One door card is Damaged from the Car catching it when being moved. There is also a few other trim bits for a MK2 plus Super Minx I beleive. There are various bits in there for a MK1 Sceptre too along with stuff for both MK1 and 2.

Post Reply