Page 2 of 5

Re: Looking for a 1725 Holbay Engine.

Posted: Sun Mar 10, 2013 5:14 pm
by djnippa
I read somewhere else that AM3 is Holbay, but it doesn't necessarily mean it's got the flat head high compression pistons.
They could have been replaced with standard pistons due to availability.

Re: Looking for a 1725 Holbay Engine.

Posted: Sun Mar 10, 2013 7:17 pm
by rootesmadnick
thats true, but flat tops are available still, the crankshaft was also steel rather than cast iron if memory serves, there were other differences, but off top of my head I cant think of them sorry.. oh hang on.. plate under oil filter has TWO things bolted into it, distributor has NO vaccumn advance fitted (was done using weights) if it has the 40's on it you MUST get the orange fibreglass airbox and pancake air filter that goes with it or else the jetting wont run right.. believe me I know this from experience

Re: Looking for a 1725 Holbay Engine.

Posted: Sun Mar 10, 2013 7:18 pm
by rootesmadnick
thats not gospel about the oil filter base.. jsut a vague recollection I could be wrong

Re: Looking for a 1725 Holbay Engine.

Posted: Sun Mar 10, 2013 9:25 pm
by djnippa
If I eventually get one, I'll be putting my twin Weber DCOE 40's on it for sure.
I've already talked to a racing specialist in East Sussex who can put it on a rolling road to tune them in too perfection.
The main problem is space, as they can hit the servo in a MK2 Sceptre.

Re: Looking for a 1725 Holbay Engine.

Posted: Mon Mar 11, 2013 5:48 pm
by rootesmadnick
when putting the 40's ina mk2 bear in mind you will have to get the inlet refaced to correct the angle of the carbs, as the hunter motor leans over 10 degrees, whereas mk2 motor is bolt upright. Never had any issues with servo clearance on my mk2 though when we tried holbaying it..the carbs are jetted to run with that external air box, NOT using it will mean a full rejet of the carbs which would be a nightmare as far as im concerned, especially when you consider how smoothly they ran with the stock airbox

Re: Looking for a 1725 Holbay Engine.

Posted: Mon Mar 11, 2013 6:46 pm
by djnippa
Have you got a photo of the air box?

Re: Looking for a 1725 Holbay Engine.

Posted: Tue Mar 12, 2013 6:44 am
by rootesmadnick
not off hand, its an orange fibreglass scoop that goes over the back of the carbs, leading to a thick flexipipe which in turn went onto a pancake air filter mounted on the front of the inner wing (cold air scoop you see). Just had a quick google but cant find anything at the moment

Re: Looking for a 1725 Holbay Engine.

Posted: Tue Mar 12, 2013 10:42 am
by djnippa
Is this it?

Image

Unfortunately it won't fit in my Sceptre MK2, as the brake servo is where the pancake is.

Image

Re: Looking for a 1725 Holbay Engine.

Posted: Tue Mar 12, 2013 10:38 pm
by rootesmadnick
pretty sure we had the box the other way round and had the pancake up the top end, it was a long time ago now.. but yes thats the proper airbox and the key to running the proper 40's on a holbay

I have a Holbay Engine for sale

Posted: Sat Mar 23, 2013 6:14 pm
by gijoe
Hello i was wondering where would be a good place to post this,
I have a Holbay engine w/ trans for sale,
i apoligize but i dont know how to post a picture.
located in California ,thanks you
icu96@hotmail.com

I have a Holbay Engine for sale

Posted: Sat Mar 23, 2013 6:29 pm
by gijoe
2295438670_e82c1242be_z.jpg
Hello
Yes I have a Holbay engine for sale, i dont know much about it,
engine and tranny ,
icu96@hotmail.com
thank you

Re: Looking for a 1725 Holbay Engine.

Posted: Wed Mar 27, 2013 7:32 pm
by twin40dave
Hi guys ive got a holbay engine fitted in my mk3 humber sceptre and ive just had it tuned at dave Baskerville autos in bude devon he's got a rolling road and he specializes in classics he's tuned it and rejeted it to run without the airbox I must say it runs and sounds great

Re: Looking for a 1725 Holbay Engine.

Posted: Sat Mar 30, 2013 8:11 pm
by gijoe
Hello
I have this Holbay Engine w/ trans
for sale, i know little to nothing about
except they are VERY hard to find especially
in this condition, price still working on this
taking into consideration it's great condition
California
thank you


djnippa wrote:I know they are few and far between,
but I'm looking for a 1725 Holbay Engine H120.
Any condition considered, providing it's all there.
My current standard engine needs the thrust bearing replacing, and hardened valve seats dropped in to take unleaded petrol.
So I figured I might as well work on another more powerful engine, that I can finally put my Twin Webers DC40's on.

Any leads appreciated.

Re: Looking for a 1725 Holbay Engine.

Posted: Sat Mar 30, 2013 9:21 pm
by djnippa
I've sent you an email.

Re: Looking for a 1725 Holbay Engine.

Posted: Sun Mar 31, 2013 9:03 am
by rootesmadnick
for the record these engines are safe for unleaded, the valve seats are already hardened, did thousands of miles in mine and never once had to let teh tappets out