Looking for a 1725 Holbay Engine.
- djnippa
- Posts: 142
- Joined: Sat Aug 04, 2012 6:41 pm
- Location: Streatham, London
Looking for a 1725 Holbay Engine.
I know they are few and far between,
but I'm looking for a 1725 Holbay Engine H120.
Any condition considered, providing it's all there.
My current standard engine needs the thrust bearing replacing, and hardened valve seats dropped in to take unleaded petrol.
So I figured I might as well work on another more powerful engine, that I can finally put my Twin Webers DC40's on.
Any leads appreciated.
but I'm looking for a 1725 Holbay Engine H120.
Any condition considered, providing it's all there.
My current standard engine needs the thrust bearing replacing, and hardened valve seats dropped in to take unleaded petrol.
So I figured I might as well work on another more powerful engine, that I can finally put my Twin Webers DC40's on.
Any leads appreciated.
-
rootesmadnick
- Posts: 272
- Joined: Fri Feb 01, 2008 7:42 pm
- Location: lumbering in a humber somwhere !!
- Contact:
Re: Looking for a 1725 Holbay Engine.
standard alloy head motor will run unleaded, did 20 thousand miles or so on mine with no issues at all..
Good luck on the Holbay search, they tend to make silly money and get snapped up. Personally id get a standard 1725 and rebuild it with some flat top pistons and a mild cam, wont be the holy grail of Holbayness but it would go respectably
Good luck on the Holbay search, they tend to make silly money and get snapped up. Personally id get a standard 1725 and rebuild it with some flat top pistons and a mild cam, wont be the holy grail of Holbayness but it would go respectably
I fix things!!
- djnippa
- Posts: 142
- Joined: Sat Aug 04, 2012 6:41 pm
- Location: Streatham, London
Re: Looking for a 1725 Holbay Engine.
Everyone I speak to says the alloy head will take unleaded without adding lead substitute, but also everyone I speak to uses lead substitute just in case. #enginefear. So it's a bit of a contradiction.
I had also considered doing that to the engine, the Holbay Racing guy I spoke to, said I could also bore out the pistons to a max of 1840cc, which would get a bit more power, but in the end it would have to go to a specialist and cost me more to do that. £1600-£2000 !!!
So I'd rather drive the car with the Original engine (thrust bearings gone, and uneven piston compression ratios) for now, while another one is being totally restored, and bits are polished.
Then I can just drop in the engine, in half a day once it's ready.
Although I'd lose the 'numbers matching' on engine, gearbox, car etc.
I'd still keep the Original engine, and sell it with the car.
I had also considered doing that to the engine, the Holbay Racing guy I spoke to, said I could also bore out the pistons to a max of 1840cc, which would get a bit more power, but in the end it would have to go to a specialist and cost me more to do that. £1600-£2000 !!!
So I'd rather drive the car with the Original engine (thrust bearings gone, and uneven piston compression ratios) for now, while another one is being totally restored, and bits are polished.
Then I can just drop in the engine, in half a day once it's ready.
Although I'd lose the 'numbers matching' on engine, gearbox, car etc.
I'd still keep the Original engine, and sell it with the car.
-
rootesmadnick
- Posts: 272
- Joined: Fri Feb 01, 2008 7:42 pm
- Location: lumbering in a humber somwhere !!
- Contact:
Re: Looking for a 1725 Holbay Engine.
on the american sunbeam alpine forums they talk about using chevrolet connecting rods with other pistons in these engines along with all sorts of other tricks to good effect.. might be worth a read up
I fix things!!
- djnippa
- Posts: 142
- Joined: Sat Aug 04, 2012 6:41 pm
- Location: Streatham, London
Re: Looking for a 1725 Holbay Engine.
Good tip. Thanks.
-
rootesmadnick
- Posts: 272
- Joined: Fri Feb 01, 2008 7:42 pm
- Location: lumbering in a humber somwhere !!
- Contact:
Re: Looking for a 1725 Holbay Engine.
when I was running my humber I did debate using bike carbs on her as the ports are perfectly round and almost crying out for such a thing.. never got round to it though sadly
I fix things!!
-
hoppo
- Posts: 90
- Joined: Thu Dec 06, 2012 12:17 pm
Re: Looking for a 1725 Holbay Engine.
Hiya, Classic Car Weekly wednesday 23rd jan 2013 page 50 column 4 1st advert Hunber sceptre 28,000 miles HOLBAY engine with overdrive gearbox £475 Needs welding but still mot'd ready to go (so I presume it is drivable) 07879898292 01493 732579 based in norfolk Hope this may be of use you could of course get most of your money back selling the spares from the car!!!! regards mick H
- djnippa
- Posts: 142
- Joined: Sat Aug 04, 2012 6:41 pm
- Location: Streatham, London
Re: Looking for a 1725 Holbay Engine.
Sugar puffs. It was already sold.
Thanks for posting.
Thanks for posting.
-
rootesmadnick
- Posts: 272
- Joined: Fri Feb 01, 2008 7:42 pm
- Location: lumbering in a humber somwhere !!
- Contact:
Re: Looking for a 1725 Holbay Engine.
its strange.. they seem to appear out the woodwork in spurts, then none appear for ages again, the lad who I sold mine to has pulled the original engine and box (ebayed apparently) to put a ford engine and gearbox in, to say I was disappointed would be an understatement as it still had matching engine/chassis numbers but at the end of the day he paid for her so it was his to do as he pleases, I just hope the mondeo engine gives him what he hopes it will, got to say though going from 6 speeds to 5 would be a downgrade in my book.. (no overdrive?? surely thats half the fun)
I fix things!!
-
hoppo
- Posts: 90
- Joined: Thu Dec 06, 2012 12:17 pm
Re: Looking for a 1725 Holbay Engine.
HIya yet another holbay motor E-Bay Hunter GLS scruffy red supposed to be holbay motor @ £500 If yougot it I would very much like the trim if you broke it. Living in hope....Hoppo Whoops date is 28th jan 6days to run.... good luck
-
hoppo
- Posts: 90
- Joined: Thu Dec 06, 2012 12:17 pm
Re: Looking for a 1725 Holbay Engine.
another one on ebay £99.00 no distributor worth a look ....9th march 2013
- djnippa
- Posts: 142
- Joined: Sat Aug 04, 2012 6:41 pm
- Location: Streatham, London
Re: Looking for a 1725 Holbay Engine.
I'm on it. Thanks.
Keep 'em coming.
I'm also looking at one in Devon for £150, but he's got to send me photos before I journey down there.
Keep 'em coming.
I'm also looking at one in Devon for £150, but he's got to send me photos before I journey down there.
-
rootesmadnick
- Posts: 272
- Joined: Fri Feb 01, 2008 7:42 pm
- Location: lumbering in a humber somwhere !!
- Contact:
Re: Looking for a 1725 Holbay Engine.
externally not a lot to show its a holbay, if youa re going for a look, try to see teh AM number cast on the front of the head between 2+3 spark plug, am3 is holbay head am2 is standard head (99% sure on that) rocker covers can be swapped for steel ones easily enough so holbay on the cover is not enough to say its a holbay.. 
I fix things!!
- djnippa
- Posts: 142
- Joined: Sat Aug 04, 2012 6:41 pm
- Location: Streatham, London
Re: Looking for a 1725 Holbay Engine.
Wise words. I've asked for other photos.
As I can see the AM3 on the photo.
It's a bit worrying the guy selling it only has 1 feedback.
As I can see the AM3 on the photo.
It's a bit worrying the guy selling it only has 1 feedback.
-
rootesmadnick
- Posts: 272
- Joined: Fri Feb 01, 2008 7:42 pm
- Location: lumbering in a humber somwhere !!
- Contact:
Re: Looking for a 1725 Holbay Engine.
as I said im pretty sure am3 is holbay, might be worth some of you hunter owners just confirming you have an AM2 head on your cars for us please if you can
I fix things!!