Zenith Carburetor linkage

Post Reply
rhythmrider
Posts: 89
Joined: Mon Sep 02, 2013 6:58 pm

Zenith Carburetor linkage

Post by rhythmrider » Mon Nov 04, 2013 2:11 am

The old Zenith carb that I have rebuilt is missing one piece of linkage for the accelerator.

Does anyone have any old bits around the garage with which they are willing to part?

It's part number 66 in the diagram below.
Of course if you have number 65 to go with it, I would not mind...

Thanks,
Dana
You do not have the required permissions to view the files attached to this post.

nzchevy
Posts: 22
Joined: Sun Aug 25, 2013 5:05 pm

Re: Zenith Carburetor linkage

Post by nzchevy » Mon Nov 04, 2013 8:08 pm

I have got an old Solex carb. which has the same part on it. If you let me have your details I will send it to you.

Regards

Roger

rhythmrider
Posts: 89
Joined: Mon Sep 02, 2013 6:58 pm

Re: Zenith Carburetor linkage

Post by rhythmrider » Tue Nov 05, 2013 7:26 am

Roger, for some reason my reply got lost.
Will send again.

Thank you very much.
That's terrific!

Will send you my mailing address in a PM

One thing I did not say is that I am in the USA.
I hope that is ok.
Would be happy to reimburse any postage.

Regards,
Dana

rhythmrider
Posts: 89
Joined: Mon Sep 02, 2013 6:58 pm

Re: Zenith Carburetor linkage

Post by rhythmrider » Thu Nov 28, 2013 6:31 pm

Roger,
I wanted to thank you very much for the linkage piece.

As it turns out the throttle shaft diameter on the Solex is a little bigger than on the Zenith.
So I had a buddy weld up the hole to a smaller size and then I filed it to fit.

Now it works great!
Thank you again for your time and generosity in shipping me the part.
(If you ever need any help with Chevy parts, let me know)

Best regards,
Dana
linkage.jpg
You do not have the required permissions to view the files attached to this post.

nzchevy
Posts: 22
Joined: Sun Aug 25, 2013 5:05 pm

Re: Zenith Carburetor linkage

Post by nzchevy » Thu Nov 28, 2013 9:02 pm

Dana,

Glad to be of assistance, I'm glad the part arrived O.K.

I might take you up on the Chevy parts one day. I've got a '50 4Dr Fleetline and a '46 Pick Up, which both need work. The Pick Up is from New Zealand.

Ironically I think I told you I sent my Zenith carb off to be rebuilt but it turns out it was the wrong one and my car should actually have the Solex fitted. However the throttle linkage on the Solex was not right for my car because I've got an automatic and the linkage is slightly different. I've now sent the Solex off to be rebuilt.

Good luck with the rest of the work.

Regards

Roger

rhythmrider
Posts: 89
Joined: Mon Sep 02, 2013 6:58 pm

Re: Zenith Carburetor linkage

Post by rhythmrider » Thu Nov 28, 2013 10:20 pm

I hope I did not put you in a bind because you now have no linkage on the Solex!

Unless you are going for period perfect, I'd probably go with a new Weber.
(They certainly are cheap enough new)

The only reason I rebuilt the Zenith myself was for the fun of it.
Everyone says the Weber give better performance AND economy than the Solex or Zenith.

Am told the 34 ICH is a bolt on replacement.
http://www.webercarbsdirect.com/34_ICH_p/15290.027.htm

Dana

Post Reply